> Bear
BEAR PIVOT CUP CHOICES! If you're looking to replace the Pivot Cups of your Bear Grizzly Trucks - please read carefully! Pivot Cup sizes are different among some seemingly-same Bear Grizzly Trucks before Generation 5 came out around 2014. If your Trucks have '5.01' on the hanger (or if you have purchased them new from Landyachtz or a reputable Skate shop within the last 3 years) - your chances are good the Bear Grizzly 5.01 Pivot Cups are the proper size. The only sure way to be sure what cups you have is to measure the diameter of the cup with calipers. Generation 5 will be about .70" (17.8mm) the other size (Vintage) will be .74" (18.8mm). It seems like such a small difference, but it's enough of a difference that the Pivot Cup you order will either drop right in the hole, or there's no possible way you can fit it in the hole.....As you can imagine, this is a bit of a nightmare for us to deal with on an aftermarket basis!
*** We have found a handy trick for figuring out which Bear Trucks you have! You need a U.S. Dime - remove the stock pivot cup and holding the dime between your thumb & finger, slide the dime into the pivot cup hole - if it slides in nice & snug and does not move, you have a Generation 5 Truck. If the dime is loose in the hole and you can hear it rattle when you shake it, then you will need the Vintage Truck Pivot Cup.
So, if you are unsure or cannot measure your Pivot Cups, you should order both sizes - the 5.01 and the 'vintage' - and return the pair that does not fit (at your own expense, which is $2.66 - $3.09 within the U.S. depending how far from California you live), if you want a refund on the unused cups. We apologize, but we simply can not be responsible for the Pivot Cups not fitting in the older Bear Trucks. Feel free to contact us and we will do our best to help - but even then, it can be really hard for us to tell for sure.....
- Bear - Gen. 6
- Bear - Grizzly 5.01 & Later
- Bear - Kodiak
- Bear - Polar Bear
- Bear - Precision
- Bear - Smokey
- Bear - Vintage
-
APS Barrel
$7.99APS Barrel Longboard Bushings are sold as a Pair with a sticker and No Washers are included. Bushing Height: 0.6" - Bushing Diameter: 0.98" The APS compound is very lively, which offers high rebound with lots of control and lean. This...$7.99 -
KranK Barrel
$9.99 - $18.99Krank Barrel Longboard Bushings are sold as a Pair with a sticker and No Washers are included. Bushing Height: 0.6" - Bushing Diameter: 0.98" Performance Under Pressure - The KranK Formula has quite a bit of adjustability. You can tighten the...$9.99 - $18.99 -
APS Cone
$7.99Cone skateboard bushings are sold as a PAIR with a sticker and NO WASHERS are included: The APS formula rides a couple of points softer than they test, so order accordingly Hard durometer bushings...$7.99 -
APS Tall Barrel
$8.99Sold as Pair with Sticker. .975" Dia x .75" High (24.77mm Dia x 19mm High) APS rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95a - 97.5a) are for heavier-weight riders (over 125lbs)...$8.99 -
APS FatCone
$8.99FatCone skateboard bushings are sold as a PAIR with a sticker and LARGE FLAT WASHERS are included: The APS formula rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95a - 97...$8.99 -
KranK Canon
$9.99Sold as Pair with Sticker. Designed specifically for use in Paris Trucks as well as those that have a slightly larger bushing seat. The slightly larger shape will fill that seat snugly, thus eliminating the chance of dead-space or...$9.99 -
KranK Cone
$9.99Sold as Pair with Sticker. .975" Dia x .60" High (24.77mm Dia x 15.24mm High) Cones offer the lowest resistance and stability of bushing shapes which can allow your trucks to easily achieve their full lean and turn. The Cone / Cone setup is for...$9.99 -
WFB Barrel
$9.99WFB Barrel Longboard Bushings are sold as a Pair with a sticker and No Washers are included. Bushing Height: 0.6" - Bushing Diameter: 0.98" The WFB formula will have a white powder residue on the surface. This is a good thing and...$9.99 -
APS Canon
$7.99Canon skateboard bushings are sold as a pair with a sticker and NO WASHERS are included: The APS formula rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95a - 97.5a) are for...$7.99 -
KranK Tall Barrel
$10.99Sold as Pair with Sticker. .975" Dia x .75" High (24.77mm Dia x 19mm High) For use in trucks that require Tall Bushings (such as Ronin, Bear Kodiak, Arsenal) TallBarrels offer the next step up in stability above the TallCones and are often used for a...$10.99 -
APS Short Street Cone
$7.99Sold as Pair, with small cup washers & a sticker Sized to fit properly in conventional "Indy-style" trucks Custom APS Urethane Formula for ultra-performance and sweet rebound .975" Dia x .4" High (24.77mm Dia x 10.2mm High) Stiffer bushings...$7.99 -
KranK Short Street Cone
$8.99Sold as Pair with Small Cupped Washers & a Sticker The ShortStreetCone / StreetCone setup is for those looking for a very carvy or surfy feel. The ShortStreetCone / StreetBarrel setup is for those looking for a carvy or...$8.99 -
KranK FatCone
$11.49Sold as Pair with Flat Washers and Sticker. .975" Dia x .60" High (24.77mm Dia x 15.24mm High) FatCones have the same initial stability as a Barrel but as you lean, they offer progressively higher resistance the further you go. The...$11.49 -
APS Chubby
$8.99Chubby skateboard bushings are sold as a PAIR with a sticker and LARGE FLAT WASHERS are included: The APS formula rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95a -...$8.99 -
KranK Chubby
$11.49Sold as Pair with Large Flat Washers and a Sticker. .975" Dia x .60" High (24.77mm Dia x 15.24mm High) Chubbys offer the highest stability of all the shapes we offer & work best in a truck that has a stepped bushing seat to take...$11.49 -
WFB Cone
$9.99Sold as Pair with Sticker. .975" Dia x .60" High (24.77mm Dia x 15.24mm High) APS rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a) are for heavier-weight riders (over 125lbs)...$9.99 -
KranK Short Street Barrel
$8.99Sold as Pair with Small Flat Washers and a Sticker. The ShortStreetBarrel / StreetBarrel setup is for those looking for higher stability at higher speeds but still highly maneuverable. The ShortStreetBarrel /...$8.99 -
WFB Tall Barrel
$10.99Sold as Pair with a Sticker .975" Dia x .75" High (24.77mm Dia x 19mm High) WFB rides a couple of points softer than they test, so order accordingly. Hard durometer bushings (95.5a - 93a) are for heavier-weight riders (over 125lbs)...$10.99 -
KranK Magnum
$11.49Sold as Pair with Large Flat Washers & a Sticker! Choose the Magnum shape if you're using Paris Trucks or any truck that has a slightly larger bushing seat. The slightly larger shape will fill that seat snugly, thus eliminating the...$11.49 -
Bear Vintage Pivot Cup
$13.95Check out Bear Vintage Recommended Products for more info on the trucks. These Pivot Cups are sold as a pair and fit into Bear Vintage Trucks and are available in Green. The Dime Trick - Hold a dime between your thumb & finger and slot it...$13.95 -
APS Short Street Barrel
$7.99Sold as Pair, with small flat washers & a sticker Sized to fit properly in conventional "Indy-style" trucks Custom APS Urethane Formula for ultra-performance and sweet rebound .975" Dia x .4" High (24.77mm Dia x 10.2mm High) Hard...$7.99 -
APS Tall FatCone
$10.49Sold as Pair with Large Flat Washers & a Sticker .975" Dia x .75" High (24.77mm Dia x 20mm High). Custom urethane blend. APS rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95a - 97.5a) are...$10.49 -
WFB Canon
$9.99Sold as Pair with a Sticker WFB ride a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a) are for heavier-weight riders (over 125lbs) and allow for a nice tight set-up...$9.99 -
APS Magnum
$8.99Magnum skateboard bushings are sold as a PAIR with a sticker and LARGE FLAT WASHERS are included: The APS formula rides a couple of points softer than they test, so order accordingly Hard durometer...$8.99 -
WFB FatCone
$11.49Sold as Pair with Large Flat Washers & a Sticker .975" Dia x .60" High (24.77mm Dia x 15.24mm High). WFB rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a) are for...$11.49 -
WFB Chubby
$11.49Sold as Pair with Large Flat Washers & a Sticker .975" Dia x .60" High (24.77mm Dia x 15.24mm High) APS rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a) are for heavier-weight...$11.49 -
Bear Grizzly / 5.01 Pivot Cup
$13.95Check out Bear Grizzly Recommended Products for more info on the trucks. WFB Ace Pivot Cups are sold as a pair and fit into Bear Grizzly 5.01 & Later. These pivots are available in Green. Riptide's Premium WFB Pivot Cups are a perfect upgrade...$13.95 -
APS Tall Cone
$8.99Sold as Pair with Sticker. .975" Dia x .75" High (24.77mm Dia x 19mm High) APS rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95a - 97.5a) are for heavier-weight riders (over 125lbs)...$8.99 -
KranK Tall FatCone
$13.99Sold as Pair with Flat Washers and Sticker. .975" Dia x .75" High (24.77mm Dia x 20mm High) TallFatCones have the same initial stability as a TallBarrel but as you lean, they offer progressively higher resistance the further you go...$13.99 -
Bear - Polar Bear Pivot Cup
$13.95Check out Polar Bear Recommended Products for more info on the trucks. WFB Ace Pivot Cups are sold as a pair and fit into Polar Bear Trucks. These pivots are available in Green. Riptide's Premium WFB Pivot Cups are a perfect upgrade to your...$13.95 -
Bear Kodiak Pivot Cup
$13.95Check out Bear Kodiak Recommended Products for more info on the trucks. WFB Ace Pivot Cups are sold as a pair and fit into Bear Kodiak Trucks. These pivots are available in Green. Riptide's Premium WFB Pivot Cups are a perfect upgrade to your...$13.95 -
WFB Magnum
$11.49Sold as Pair w/Washers & a Sticker 1.10" Dia x .60" High (24.77mm Dia x 15.24mm High) WFB rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a) are for heavier-weight riders (over...$11.49 -
KranK Tall Cone
$10.99Sold as Pair with a Sticker .975" Dia x .75" High (24.77mm Dia x 20mm High). KranK rides a couple of points softer than they test, so order accordingly. Harder KranK durometer bushings (93a) are for heavier-weight riders (over 140lbs) as...$10.99 -
WFB Tall FatCone
$13.99Sold as Pair with Large Flat Washers & a Sticker .975" Dia x .75" High (24.77mm Dia x 20mm High). Custom urethane blend. WFB rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a)...$13.99 -
WFB Tall Cone
$10.99Sold as Pair with a Sticker .975" Dia x .75" High (24.77mm Dia x 20mm High). Custom urethane blend.APS rides a couple of points softer than they test, so order accordingly Hard durometer bushings (95.5a - 93a) are for heavier-weight...$10.99 -
Bear Gen 6 Pivot Cup
$13.95Sold as a Pair with Sticker! Specifically designed for each truck Lively & Responsive Hand-poured into Custom-made molds, then the cup end is machined to fit the truck's base plate perfectly No machining imperfections and no heat-affected zone...$13.95 -
Bear Precision Pivot Cup
$13.95Check out Bear Precision Recommended Products for more info on the trucks. WFB Ace Pivot Cups are sold as a pair and fit intoBear Precision Trucks. These pivots are available in Green. Riptide's Premium WFB Pivot Cups are a perfect upgrade to your...$13.95